Step 3: The umbrella frame with canopy can be rotated 360°. To open the canopy, turn the canopy crank handle (E2) clockwise until the canopy is fully opened. Release grip to lock umbrella canopy frame into place. Step 2: To open the umbrella, squeeze grip on the canopy glide handle (E3) and slide up or down on the pole to achieve desired canopy angle. Step 1: Unfasten storage straps around the canopy and pole. Align pinhole on both cranks handles to corresponding pins to lock. Step 4: Attach 360° crank handle (E) to pole and canopy crank handle (E2) onto canopy glide handle (E3). When finished, slide the pole support cap down to rest on top of the blow-molded base. Place each base section onto the cross legs as shown in the diagram, lift support cap (L) for the two inside base sections. Step 3: Fill each base (A & B) with sand and fasten cap (M). Failure to do so will result in a weight imbalance and cause the umbrella to tip, causing damage and/or personal injury. It is recommended at least 150 kg (330 lbs) of weight be placed on cross legs to ensure stability. Add water to wet the sand and continue to fill each section with water up to the top. WARNING: Before opening the umbrella, complete assembly as instructed in the manual. Finally, tighten bolts with an adjustable wrench or open-end wrench (not included). Adjust the umbrella frame to be sure it is positioned correctly on base. Use one washer and one bolt per hole, do not overtighten. Lift the pole support cap (L) up to align holes on the bottom of the umbrella frame with holes on top of cross legs (C,D).
Step 2: Attach the umbrella frame (N) to cross legs by using bolts (GG) and washers (HH) found in a blister pack. Step 1: Place lower cross leg (C) on the ground, line up notches, and place upper cross leg (D) over lower cross leg (C). that may be wrapped in protective materials.ĬAUTION: An additional person is suggested to assist with inserting the umbrella frame into the pole holder. Be careful not to throw away small parts such as bolts, washers, etc. You only need your original canopy.Tools Required for Assembly (not included) Picture Description Quantity Adjustable Wrench 1 Hardware Contents Part Picture Description Quantity GG Outer Hex Bolt M10-1.5x20A2-70 4 HH Flat Washer M10A2-70 4 Package Contents Part Description Quantity A Blow Molded Base Outside 2 B Blow Molded Base Inside 2 C Lower Cross Leg 1 CAN Canopy (on the umbrella frame) 1 D Upper Cross Leg 1 E 360.Crank Handle 1 E2 Canopy Crank Handle 1 E3 Canopy Glide Handle 1 L Pole Support Cap 1 M Blow Molded Base Cap 4 N Umbrella Frame (with canopy) 1 Assembly Instructionsĭo not use sharp tools or equipment such as a knife or scissors when removing the protective material it may damage the product. These are complete replacement frames for your patio/market umbrella (lower pole, upper rib support section and finial top). Umbrella manufacturers use various specs, so let us help you in picking a frame that will fit your existing canopy. Replace your broken patio market umbrella frame with one of our sturdy frames in wood aluminum and all the features like crank and tilt.
#REPLACEMENT CANOPY FOR FRONTGATE CANDELAIR UMBRELLAS HOW TO#
See this video guide on how to accurately measure an existing umbrella for compatibility
We suggest you measure the radius of your existing frame. Shade USA has a particular method for measuring to ensure that our frames are compatible with your canopy. On each product page you will find a link to our helpful how-to-measure video to guide you in the process. Important: The first step in replacing an old worn or broken patio umbrella frame is to accurately measure your existing umbrella to ensure a good fit with the replacement. All frames include the upper canopy support frame, lower center support pole and finial.
Replacement frames for patio umbrellas in all the popular sizes.
0 kommentar(er)
